All Activity

There’s a 1/4” rubber shim that fits in between the bumper and the fiberglass body which will fill some of that gap. The gap on your Avanti does look excessive. I’d add a second rubber shim, then tighten the bolt to crank it in.

Installed the rear bumper and have excessive side clearance. Over an inch from the fiberglass to the mounting pad on the bumper. I think I need to bend the bumper. What is the standard gap? As it is the bolts do reach.

Studebaker recommended replacing the disc brake pads on their 1963 and 1964 passenger cars equipped with Bendix disc brakes when the pad thickness wore down to……?……. 1) 3/16”…..2) 1/4”…..3) 5/16”…..or…..4) 3/8”

In my 63, I installed the 51 by moving the oem front mounting bracket and making an aluminum battery frame. The frame is notched out around the terminals and then covered with some automotive rubber trim. This also gave me room to move the radiator overflow tank to the left side so I can make a CAI and place it on the right side.

Ben, I may have one. Please check your messages. Thanks

I initially thought the same thing but then remembered it’s a fiberglass body and the bracket could lean against the positive post and never go to earth/ground.

Note that the early Avanti boosters have 4 studs, and later models have two studs.

I'm not very knowledgeable on the subject of Avanti brake boosters, but "Booster Dewey" in Portland Oregon rebuilt several Avanti II brake boosters for me many years ago, and I think an original 1963 Avanti booster as well (the boosters may have been the same). I've owned a half-dozen or so Avanti's over the years but have not driven my one remaining Avanti for the past 10 years. https://www.powerbrakebooster.com/

Thanks for all the responses and info. Good luck all.

Don't know if helpful, but the parts book shows that the hood ornament, including insert, changed at serial number 4879.

I have no documentation to support this, but I recall seeing early round light Studebaker Avanti‘s with a gold ‘S’ on the hood, and silver ‘S’s’ on the cars earmuffs!

The mounting holes were on all of them. My early serial # 63 has the holes but never had a grille.

Somewhere during the '63 model run the grille was made standard. --Dwight

It depends on your car's serial number. Earlier '63 Avantis came with a gold "S" and later '63s came with a silver one. I don't know the serial number at which Studebaker changed from gold to silver, but someone does. --Dwight

https://midwestbooster.com/ here is where i've bought my rebuild kit , item code 2502303 k

So , i'm gone take a look to my rebuild kit invoice

Does anyone know where I can get this? Do you have one you can sell me? I can't find it anywhere. "Things the Shop Manual Never Told You" by Stan Gundry

Mopar ‘B’ body….. A 1969 Dodge Charger for example.

The mounting holes are there where one was in place

Hello RQA025, NAPA could not find the number NBB5473603. Further, he did not know Mopar B Body. Do you, or does anyone, have any other replacement suggestion(s)? Thanks

I have a 63 Avanti. I have two sets of Lazy S's. One set is silver and the other is gold letters, Which is correct for the 63 Avanti?

One thing to look out for regarding the front shocks. The shocks I bought, and all others that I looked at, had the same problem. The lower flange was 3" from end to end.....the center of the mounting holes on the lower A-arm are 3.5" apart. I eventually solved my issue by extending each side of the lower flange with 3/16 stock flat iron, carving out an slot for the carriage bolt slots on the welded extensions. I posted pictures of the extensions in a post last year

Here are a few more pictures.

GOOD MORNING JIM I HAVE A SET OF REAR SHOCKS RECENTLY REMOVED FROM RQB3263/81 HERE IN NORTH FLORIDA ALONG WITH OTHER STUFF ...give me a call 386-466-6434 bill gregg .....thanks

Bought mine from our old friend Dave Thibeault…Always on top of Avanti specific items!