-
Posts
528 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by wildfelr
-
-
GEORGE ALSO HAS A FULL PAGE ADD IN THE AVANTI MAG.....
-
RQB3263/81/305 My 81 has the original metal tag on rear gear cover bolts indicating 2.72 ....this is great especially with the 700r4 trans I installed 5 yrs ago... now taching 1800 at 70 MPH.... with that my 305 should last a long time ...In fact the lower end has already lasted 41+ yrs ...your set up is probably identical but with a TH350 trans unless someone has been messing around with a perfectly good and beautiful cruiser .... keep up the good work .....BILL in Fl
-
RQB3263 How many bolt/washers do you need and what is your ship to address ?
-
RQB3263/81/305 3263 Had steelies yrs ago so I replaced them w 16" 07-09 Mustang pictured here .... they are a great looking wheel and were inexpensive at the time.... they did req adapter/spacers to go from GM pattern to Ford, avail on line 1 1/4" in front and 1" in rear all good...I got 5 so I have a matching spare..... the tires in pic are 205/60R16 ....I hope to be replacing them with Vogue Gold Line 225/60R16 by end of 2022.... keep up the good work.....BILL
-
RQB3263/81 .... WOW What a beautiful car !!
-
-
RQB3263/81 .... I dont believe the quick steer links will change the turn radius..... it will only go as far as the suspension geometry / built in stops allow....now it may get to the stop slightly quicker ....but no change in the turn radius......BILL
-
RQB3263/81.......how many bolt/washers do you need ??
-
RQB3263/81 ..... I JUST FINISHED REPLACING BOTH REG./MOTORS W/ NU-RELICS....and sure I have these washers..... i will check....text me at 386-466-6434 ....BILL
i checked my leftover parts and i have 12 i think with bolts...... bill
I want a spoiler as in the attachment below .....please keep in touch ...... BILL
-
-
RQB3263..... POWER WINDOW PROJECT FINISHED...... the NU-RELICS reg/kit worked just fine..... FYI....masking tape will not hold the window up when disconnected.... use duck tape....... use an 90 degree angle /air grinder w/ a 3' cutting wheel to cutaway the fiber glass web for clearance on the motor.... do replace roller on track bar two bolts easy 5 min..... BTW ... I now have both R&L oem running when removed reg./motor assys. for sale or trade ....see you all in Gainesville in Sept...... BILL
-
RQB 3263.....Well it all works fine now....I think a wire was stuck in the gear segment ....anywat door panel going on today and pass panel being removed.....this project could be finished tomorrow........ is there any value in the 2 old reg/motor take-outs I have ??? I would actually like to trade them for the front spoiler Ive been looking for....BILL
-
RQB3263/81/305....11PM....i received my NU-RELICS motor/regulator kit at 6pm today.....the kit is fine.... first test all the way up and down just fine.....but after that only up 3 inches......ive had it in and out a couple times ...i think the bleeding has stopped .....try again tomorrow....BILL
-
RQB3263/81/305.... MY Nu-Relics R&L reg. motor assy. due in today Tuesday..... so I decided to go ahead and remove the old one based on the you-tube video which ive watched at least 3 times...... very helpful ....so here is the up date on the old removal........good news with the door panel off and battery disconnected ...ONE HOUR to remove having not done it before ...... what may have helped is it came out in two pieces.... I suspect that disconnect was the source of the failure.... A couple things not defined in the video...(1) the upper roller #3 I managed to get the clip off with needle nose pliers and a very small screwdriver.... I have now removed the upper track (two more 7/16 wrench bolts).... It would appear that is the only way to install the new roller....BTW it appears it was all lubed with white lithium grease from the factory (bad idea) (2) there are only 2 wires to the motor a red and a yellow ..i am sure the diagram will address this (3) there are several wires running along the bottom of the inside below all this monkey motion that I have no idea where they go and are not part of this power window assy as best I can tell.... NEXT I will trim the fiberglass part inside the door (5 minutes) .... remember the good news....one hour if you have never done a removal before.....BILL
-
-
RQB3263/81/305 Yes.........I replaced my electronic Q-JET with a NON e-jet.....one wire....direct bolt in identical easy ...rebuilt ...less than $200 and works perfectly for 7 years now..... BILL
-
RQB3263/81 WELL i JUST ORDERED A SET (R&L) power window regulators from Nu-Relics .....and with the videos and help here ....I am happy to solve this problem forever
I hope to have them all done by Sept Meet here in Gainesville, fl.... THANKS again to all and for sure please keep in touch.... Happy BILL
-
RQB3263/81/305 ... i JUST WATCHED THE VIDEO ON THE INSTALLATION OF THE nEW rELICS POWER WINDOW REGULATOR KIT INSTALL.... (Sorry for screaming but I am a happy camper with this info)...does any one else have experience installing/purchasing this kit ?? please jump in here .... thanks ....BILL IN FL 386-466-6424 CELL
-
OH WOW THANKS..... it looks like this is the way to go and the video is great ....thanks again.... RQB3263 and I appreciate this tremendously
-
RQB3263/81 .... Well we got the drivers door panel off today ... thats all the good news for today .... It appears the regulator has suffered some kind of a failure ... so I am looking to buy a new regulator complete with motor.... so along with looking to buy I am also looking for guidance .... (help)... I am now also the proud owner of 14 little orange rollers that I will probably never use .... you all please keep in touch ....BILL RQB3263
-
RQB3263/81 THANKS ...actually thats encouraging ..... I JUST GOT 4 ROLLERS FROM Steven Cade here in N Florida..... so if thats the problem Wednesday should be a good day..... If it fixes the left I may go ahead and do the right side before I forget how ...... THANKS .... BILL
-
RQB3263/81 YES I did ...the last problem was the window jumped past and got hooked on the down stop angle... same window.... probably just another couple hundred bucks.... aaaaarg
-
RQB3263/81/305 ..... while raising drivers door power window it made a loud clunk and the window dropped like a Gaitan and disappeared down into the door ....I have an appointment next Wednesday with L&S TRIM to remove the door interior panel..... What do you all think I will find ?? THANKS ...... BILL...(see you all in Gainesville in Sept)
-
RQB3263 NEITHER OF THOES HAVE THE WHITE/GOLDLINE LIKE VOGUE ....MY BRIDGESTONES HAVE MANY MORE THOUSANDS MILES LEFT KEEP UP THE GOOD WORK .....BILL
Fuel tank options?
in 1965-83 Avanti
Posted
George number in tenn is 865-908-6100 ...... I have had zero luck actually getting one item from him .... many calls finally gave up