Fourward Posted August 22, 2023 Report Share Posted August 22, 2023 I am removing the starter. The shop manual says to just remove it but there is a lot of stuff in the way. Do I have to remove the exhaust pipe or something? Too tired to crawl back under there right now, Link to comment Share on other sites More sharing options...
brad Posted August 22, 2023 Report Share Posted August 22, 2023 (edited) If you have stock exhaust (notR3), then you can extract the starter without removing anything else. Slide it rearwards until the nose clears the opening, then tilt it down and the far end up. Edited August 22, 2023 by brad Link to comment Share on other sites More sharing options...
Fourward Posted August 22, 2023 Author Report Share Posted August 22, 2023 Thanks again, Brad. I will give it a go tomorrow. It does have power steering, which seems to be in the way, along with the exhaust pipe. FWIW, very original car, the wire from the solenoid to the starter has a rubber sheath over it, and, is secured by a clip integral to the frame. Link to comment Share on other sites More sharing options...
Fourward Posted August 22, 2023 Author Report Share Posted August 22, 2023 The reason why I took it out is because it is frozen. If you give it 12 volts you just get sparks. Even on a bench test. Does anyone know the fix for this, or, just send it out for a rebuilt one? Link to comment Share on other sites More sharing options...
Gunslinger Posted August 22, 2023 Report Share Posted August 22, 2023 I would have a qualified rebuilder test it and rebuild it if necessary it before getting an assembly line rebuilder do it. Link to comment Share on other sites More sharing options...
Fourward Posted August 23, 2023 Author Report Share Posted August 23, 2023 Uggghhh....I can't seem to get it out. Can you explain exactly how? Tilt it upward then come out the front? Or something. It's lying on top of the exhaust pipe which I'm about to sawzall. (I am on my back on a gravel driveway.) Link to comment Share on other sites More sharing options...
Fourward Posted August 23, 2023 Author Report Share Posted August 23, 2023 Oh, never mind, I reread the directios from Brad. Will try again tomorrow. Link to comment Share on other sites More sharing options...
mox Posted August 24, 2023 Report Share Posted August 24, 2023 I had the same problem when I had to have my starter rebuilt. I had to drop the exhaust pipe from the manifold to have enough room to drop the starter. If I recall correctly original Studebaker exhaust pipes had a flat spot near the starter which allowed just enough room to slide the starter by it. Link to comment Share on other sites More sharing options...
Fourward Posted August 24, 2023 Author Report Share Posted August 24, 2023 Yes, the only problem with dropping the exhaust pipe from the manifold is that someone cranked a bolt in there on one side instead of a stud with a nut. I got the one nut off easy enough, the bolt is imbedded in there, with a head that is starting to round. One other idea, I was just trying again. There is a metal bar with a 1 1/4 nut attached to the steering. It looks like that bar moves forward or backward by turning the wheels. I think I will have enough room if I turn that bar out of the way. Should I move it forward or backward, ...Brad? I can see it move on my other Avanti, the one I am trying to install an engine. The one with the starter is on a ramp so turning the wheel is a slightly bigger deal than just turning it. Link to comment Share on other sites More sharing options...
Fourward Posted August 24, 2023 Author Report Share Posted August 24, 2023 Pitman arm. Link to comment Share on other sites More sharing options...
Fourward Posted August 25, 2023 Author Report Share Posted August 25, 2023 I turned the wheels to the right, moving Pitman arm, that thing FELL RIGHT OUT OF THERE!!!! Almost hit me on the head. 2 minutes work. YEAH!!! Link to comment Share on other sites More sharing options...
Skip Lackie Posted August 26, 2023 Report Share Posted August 26, 2023 Good job. That's how a lot of us learned it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now