[brake cylinder diameter]

I have run into this issue, I wonder where the Vendors get theirs, the mark up is horrible. I was looking into getting a proportion valve and figuring it out. The large valves are all over the place. 

[Custom Autosound USA- 630 Receiver?]

2 hours ago, mfg said:

Wow!…Doesn’t seem right… If you purchased it new, I’d think they would take it back and furnish you the correct size…The unit I purchased fit my ‘83 Avanti with no mods..I was able to perform the entire install through the removable sunglasses opening at top center of dash.

I am working on it; this radio is supposed to be the one for 63-64's. 

[Radio Bezel for a 63?]

Thank you Kodjo, I am looking at making one myself also, thanks for pictures. Nostalgic has an article in their tech articles about the installation of these. 

[Custom Autosound USA- 630 Receiver?]

The 630 I got is supposed to be for early Avanti's, it is too small side to side 3 1/2" vs factory 4 1/2". It looks like I would have to make a custom bezel to make it work.  

[Radio Bezel for a 63?]

Thanks, the problem with Nostalgic is he ships everything Fed Ex., which is almost as much as the part.

[Radio Bezel for a 63?]

Anyone have the radio bezel P/N 1558985 laying around? Thanks

[Custom Autosound USA- 630 Receiver?]

Has anyone used one of these in their cars? They are supposed to be made to fit Avanti's with no modifications to dash radio opening. Thanks

[Parking Brake?]

Thanks for your input.

[Parking Brake?]

Thanks.

[Parking Brake?]

Thank you for information.

[Parking Brake?]

How far are your parking brake handles being pulled out before engaging the brake shoes? Mine seems to be pulled pretty far and was wondering if that could be that the shoes are worn. The shop manual does not have anything on this. Thanks  

[1963 Rear Brakes?]

Thank you for reply.

[1963 Rear Brakes?]

Are all rear brakes 11" drums? Thank you.

[Correct way to install the exterior headlight retaining ring gasket]

1 hour ago, lschuc said:

I don't know where your headlight gaskets came from, but the absolutely correct rubber gaskets and NEW round or square headlight glass is available from Endurance Built Products. [https://endurancebuiltproducts.com ]

I believe that Studebaker International also carries both of the above too.

I agree I have them, they fit great.

[Four speed vs. Powershift!]

Just my opinion, four speed cars are more fun to drive, and I think their value is higher.

[Studebaker Avanti Seat Tracks?]

Thank you for the information.

[Studebaker Avanti Seat Tracks?]

Does anyone know if the original seat tracks were carried over to Avanti ll's, if so for how many years? Thanks  

[63/64 Bucket Seats?]

Thank you, I wrote it wrong, it is 1/2 inch, I corrected it.  

[63/64 Bucket Seats?]

I believe 1/2 inch is the correct width.

[63/64 Bucket Seats?]

Thank you, that is correct.

[63/64 Bucket Seats?]

Anyone know what the correct width of the factory Hidem Gimp/piping is for these seats? Thanks.

[Door upper weather seal P/N 1351334-5?]

What is a good sealant for this installation and where should the glass fit on the seal? Thanks. 

[Heater blower filter]

Thanks a bunch, I will look for something close in size and trim it. On the rubber part, I guess it is rubber might try a split hose or a couple of flat pieces glued together.  

[Heater blower filter]

Leo, is that one you made, if so what are the dimensions? Thank you.

[Heater blower filter]

Different part number, I think.