Mark L Posted September 28 Report Share Posted September 28 (edited) I think the gaskets for my headlight covers are not properly installed. The car currently has acrylic headlight covers, and the gaskets seem too big for the covers. The attached photograph shows how my right headlight cover is currently installed. The gasket covers the exterior of the trim ring and partially covers the screw heads. I checked the index of technical articles in the AOAI magazine, but this topic was not specifically covered. I also searched the SDC Forum. I learned that the aftermarket acrylic plastic covers are smaller than the glass covers, which explains why the gasket seems too big for the cover. Regardless of the cover material, what is the correct way to install the gasket? Edited September 30 by Mark L Correct typo Link to comment Share on other sites More sharing options...
mfg Posted October 2 Report Share Posted October 2 On 9/28/2024 at 6:27 PM, Mark L said: I think the gaskets for my headlight covers are not properly installed. The car currently has acrylic headlight covers, and the gaskets seem too big for the covers. The attached photograph shows how my right headlight cover is currently installed. The gasket covers the exterior of the trim ring and partially covers the screw heads. I checked the index of technical articles in the AOAI magazine, but this topic was not specifically covered. I also searched the SDC Forum. I learned that the aftermarket acrylic plastic covers are smaller than the glass covers, which explains why the gasket seems too big for the cover. Regardless of the cover material, what is the correct way to install the gasket? I run the plastic headlamp covers on my ‘63 for general use, and save a set of NOS glass for?? The plastic covers are the same diameter as the glass… although the original glass covers may be thicker. The gasket should fit around the circumference of the cover. With the four holes in the gasket lined up with the four slots in the plastic (or the glass) covers. The gasket should not be on the outside of the chrome retaining ring. Link to comment Share on other sites More sharing options...
Mark L Posted October 3 Author Report Share Posted October 3 Thanks. On my car, neither gasket has any holes. There are no holes in the edges of the covers, only V-shaped notches at each hole location. The shop manual does not have any instructions for the orientation or stack-up/relationship of the retaining ring, gasket, cover, and the fiberglass nose panel. To remove or install the headlight bulbs, it basically says to remove and install the cover and gasket. Not helpful. A cross-section view from an engineering drawing would certainly be a big help. I was only 90 miles from the Studebaker National Museum this week, but I didn't have any time to go to see if I could find a drawing. Link to comment Share on other sites More sharing options...
lschuc Posted October 26 Report Share Posted October 26 I don't know where your headlight gaskets came from, but the absolutely correct rubber gaskets and NEW round or square headlight glass is available from Endurance Built Products. [https://endurancebuiltproducts.com ] I believe that Studebaker International also carries both of the above too. Link to comment Share on other sites More sharing options...
Dunkin Posted October 26 Report Share Posted October 26 1 hour ago, lschuc said: I don't know where your headlight gaskets came from, but the absolutely correct rubber gaskets and NEW round or square headlight glass is available from Endurance Built Products. [https://endurancebuiltproducts.com ] I believe that Studebaker International also carries both of the above too. I agree I have them, they fit great. Link to comment Share on other sites More sharing options...
Mark L Posted October 27 Author Report Share Posted October 27 Thanks. I'm thinking about springing for new replacements. I've run out of dry weather and daylight to get my brakes working, so it looks more and more like it will be parked until next spring before I can work on it again. I should have new lens covers and gaskets before it's back on the road. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now