mtgibby Posted January 19, 2017 Report Posted January 19, 2017 It is very hard to find pictures of the Avanti trunk wiring! I am trying to figure out where the plugs come out of the access channels. There's only one hole on the right, so I think I figured out that side! Thanks! Mike
brad Posted January 19, 2017 Report Posted January 19, 2017 Michael, the tail light housing needs to come back out. The wires dont come out the hole inside the trunk, but run in the hollow above the sides to the tail lights. On the drivers side, the rear largest hole is the antenna , then the next one back, is the trunk light lens. The rear smalles hole is the wires up to the trunk lid, and the back-up lights. You have to feed the flat three prong connector forwards to the other connector you have hanging out the antenna hole. You should be able to feed it back where the lens opening is to connect them. Brad
mtgibby Posted January 19, 2017 Author Report Posted January 19, 2017 Thanks Brad. I knew there must have been something I was missing! I figure this is gonna happen a lot when you try and put together a car you didn't take apart. Mike
mtgibby Posted January 24, 2017 Author Report Posted January 24, 2017 Is this where the rear license plate light wire comes inside the trunk? If it is, the previous owner filled it in when he decided to de-bumper the car.
lschuc Posted January 24, 2017 Report Posted January 24, 2017 Yes, that is the hole for the license plate light wire
mtgibby Posted January 24, 2017 Author Report Posted January 24, 2017 Thanks Lew. I will carefully drill that hole tonight! Is there a rubber grommet or bung to keep water out? Mike
lschuc Posted January 24, 2017 Report Posted January 24, 2017 No grommet is in the hole. There is a black plastic sleeve over the wire and the sleeve/wire combination fits fairly snug in the hole. Hopefully your YNZ harness should be correct and have a black plastic sleeve over the license plate wire at that point.
mtgibby Posted January 25, 2017 Author Report Posted January 25, 2017 I will look again, but I'm pretty sure that YnZ did not include the license plate light, just the female end on the trunk loom.
mtgibby Posted January 25, 2017 Author Report Posted January 25, 2017 Ok, not a wiring question, but which way does the shelf support in the trunk screw in? Flat side up or Chanel side up? I got it half way in when I realized it was probably supposed to go in flat side up. No? Thanks, Mike
lschuc Posted January 25, 2017 Report Posted January 25, 2017 It looks upside down... the Pretty sure that the flat side should face up. that slot in the top side I think is there to hold the spring catch in the access door. Mine is off now, but will check one of the others in the shop tomorrow.
brad Posted January 25, 2017 Report Posted January 25, 2017 The pictured bar is the one that is supposed to mount on the shelf itself. The piece that screws to the bulkhead is more like an angle iron, not a channel.
mtgibby Posted January 25, 2017 Author Report Posted January 25, 2017 Thanks guys. That is the angle iron shaped piece. I just couldn't find the right word to describe it at the time. I have the large channel piece off the shelf as well, waiting to get repainted after I replace the Naugahyde. I am totally missing the pass through door/hatch and will have to find one or recreate it.
brad Posted January 26, 2017 Report Posted January 26, 2017 (edited) Now I see it more clearly. You have it upside down . The screws should be on the bottom of the flange, and the carpet covers them when installed on the bulkhead. You should wait to install it until you cover the top panel above it. The naugas will have no place to hide. Edited January 26, 2017 by brad
lschuc Posted January 26, 2017 Report Posted January 26, 2017 Mike, here is what the license plate light wiring should look like. I need to use this on my other Avanti... but I should have another one somewhere. If I find it, you can have it.
mtgibby Posted January 26, 2017 Author Report Posted January 26, 2017 Thanks Lew. That is very generous! The covering in much thicker than I thought it would be. I may need to enlarge the hole I drilled. Brad, I was just test fitting the shelf to see if I painted the fawn areas under the rear glass low enough. Any special hints for covering fiberglass area/waterfall? Is the naugahyde hemmed on the far right and left sides or does the side/sail trim cover that?
brad Posted January 27, 2017 Report Posted January 27, 2017 (edited) You should use Weldwood Landau, and vinyl top adhesive. Anything else, and your asking for trouble. No hems or seams. Fold it back on itself, and do 1/2 a a time. Place masking paper between halves to keep glue off the other half your not gluing. Get a good wallpaper seam roller to follow the contours and get sharp creases around the back rest bumps. Edited January 27, 2017 by brad
mtgibby Posted January 29, 2017 Author Report Posted January 29, 2017 Brad, that looks amazing! Do you have a local source for the Weldwood Landau adhesive? The stores in the Metro East listed by the Dap website carry other Dap products, but not the Landau glue.
lschuc Posted January 29, 2017 Report Posted January 29, 2017 It's near us.... Wholesale USA, 10729 Trenton Ave, St. Louis, MO 63132 Phone:(314) 427-2400 http://wholesaleusastl.com
GlennW Posted January 30, 2017 Report Posted January 30, 2017 On 1/26/2017 at 8:30 PM, brad said: You should use Weldwood Landau, and vinyl top adhesive. Anything else, and your asking for trouble. No hems or seams. Fold it back on itself, and do 1/2 a a time. Place masking paper between halves to keep glue off the other half your not gluing. Get a good wallpaper seam roller to follow the contours and get sharp creases around the back rest bumps. very nice work! ☺
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now