I want to buy Ring and Pinion Gear

[Leo B]

Hi, Please help. 
I have Stude Avanti R2 4-speed Spicer Limited Slip (Twin Track) Dana 44. Ring with 10 bolts. Ratio 3.31
I have broken pinion which is 10 spline.
I have asked many Jeep part seller and they cannot help me. All are wrong sizes or at least wrong high ratio.
Dont find from vendors so far.
Im waiting also answers from Dan Booth and Jon Mayer.

Is there somebody who can sell me correct Ring and Pinion?
Is it possible to use other that 10 spline Pinion with new yoke?

Edited yesterday at 07:40 AM by Leo B

[mfg]

5 hours ago, Leo B said:

Hi, Please help. 
I have Stude Avanti R2 4-speed Spicer Limited Slip (Twin Track) Dana 44. Ring with 10 bolts. Ratio 3.31
I have broken pinion which is 10 spline.
I have asked many Jeep part seller and they cannot help me. All are wrong sizes or at least wrong high ratio.
Dont find from vendors so far.
Im waiting also answers from Dan Booth and Jon Mayer.

Is there somebody who can sell me correct Ring and Pinion?
Is it possible to use other that 10 spline Pinion with new yoke?

I would have a good used 3.31 ring & pinion  for the Avanti Dana ‘44’ ( non twin track) in my parts stash…. but consider me a ‘last resort’ if the vendors do not have these parts… Probably worth $150 + shipping.

BTW….. ring & pinion same for twin track or standard rear axle.

Edited 20 hours ago by mfg
Added BTW

[Leo B]

43 minutes ago, mfg said:

I would have a good used 3.31 ring & pinion  for the Avanti Dana ‘44’ ( non twin track) in my parts stash…. but consider me a ‘last resort’ if the vendors do not have these parts… Probably worth $150 + shipping.

BTW….. ring & pinion same for twin track or standard rear axle.

Please keep it for me.
Can you send your email address to leo@belik.fi

[mfg]

1 hour ago, Leo B said:

Please keep it for me.
Can you send your email address to leo@belik.fi

Don’t worry… I don’t usually sell parts but will never need these, as I have quite a few complete rear end assy’s.

I will hold them for you… Let me know.

[Leo B]

4 hours ago, mfg said:

Don’t worry… I don’t usually sell parts but will never need these, as I have quite a few complete rear end assy’s.

I will hold them for you… Let me know.

I like to buy your #537637 Ring Gear and Pinion 3.31.
email to me leo@belik.fi

[ronmanfredi]

When I rebuilt the Dana 44 in my 82 model, I bought the ring/pinion and bearing set from Summit Racing Parts.

[mfg]

2 hours ago, Leo B said:

I like to buy your #537637 Ring Gear and Pinion 3.31.
email to me leo@belik.fi

ronmanfredi suggests you check with Summit Racing Parts for a brand new set… however, I will go over to where I keep my parts tomorrow and physically inspect these two pieces… And yes.. I will email you after I do that to see if you still want them…. expect an email no later than this Sunday eve….Ed

[Leo B]

9 hours ago, ronmanfredi said:

When I rebuilt the Dana 44 in my 82 model, I bought the ring/pinion and bearing set from Summit Racing Parts.

As I understand it, the dana 44 ring and pinion has different versions for different makes and models. As well as different carriers. I have been in contact with many dealers and the manufacturer (Yukon Gears) and nowhere have I found a Ring Gear and Pinion for a Stude 1963 model with the same dimensions. Maybe 1988 is its own thing. If someone knows more, it would be good to understand.