pantera928 Posted February 10, 2022 Report Share Posted February 10, 2022 (edited) Have any of you used the following products on the insides of your Avanti frames and hog troughs and if so, what were your feelings about them? KBS Coatings 3M Cavity Wax WaxOyl POR-15 Eastwood Internal Frame coating Thanks Edited February 10, 2022 by pantera928 forgot something Link to comment Share on other sites More sharing options...
lupo Posted March 12, 2022 Report Share Posted March 12, 2022 Let's start with cavity wax. Waxoyl, Fluid film, Eastwood's cavity wax are petroleum distillates that contain calcium sulfate. Originally it was used for plates on bridges to prevent corrosion between the two pieces of steel. It is also a lubricant has grease consistency it should be applied yearly. Por-15 was developed from the Mobay Bridge aluminum pigmented moisture cured primer. KBS coatings was a por-15 dealer who lost their distributorship when por-15 went nationally and they copied everything that por-15 did. If you want to seal your inner frame and hog troughs acid treat itmetal prep with zinc them follow it up 3 coats of the aluminum pigmented moisture cured urethane. To give you a comparison zinc phosphate epoxy primer three coats wIll do between 500 to 700 hours of salt fog. Mobay's primer 14000 and if it's scratched the rust doesn't travel beyond the chip. Invest in a Harbor Freight engine cleaning gun this little sprayer will blow paint and rust remover about 3 ft. great forgetting into all your hard-to-reach places. Link to comment Share on other sites More sharing options...
lupo Posted March 12, 2022 Report Share Posted March 12, 2022 Link to comment Share on other sites More sharing options...
lupo Posted March 12, 2022 Report Share Posted March 12, 2022 Just now, lupo said: I've had this display for 30 years. 18 years people rubed their thumb and fingers over it and wore it smooth. No rust creepage and leveled up the pitting. Lacquer primer and paint over it. Link to comment Share on other sites More sharing options...
GarB Posted March 17, 2022 Report Share Posted March 17, 2022 On 2/10/2022 at 3:38 PM, pantera928 said: Have any of you used the following products on the insides of your Avanti frames and hog troughs and if so, what were your feelings about them? KBS Coatings 3M Cavity Wax WaxOyl POR-15 Eastwood Internal Frame coating Thanks Good day Pantera928. If you have never heard of Rustbullet then please take a look at their product and website. In my ever so humble opinion, it's THE best rust proofing/inhibitor on the market today. I used it on my 1968 C10 and I can sand it down and paint over it, which I've done. I don't have any pics of what I did, but I have a link you can follow: Automotive Paints | Rust Bullet Rust Prevention Products | Concrete Paint | Corrosion Preventive Treatment Repair Remover Converter Link to comment Share on other sites More sharing options...
pantera928 Posted March 17, 2022 Author Report Share Posted March 17, 2022 13 minutes ago, GarB said: Good day Pantera928. If you have never heard of Rustbullet then please take a look at their product and website. In my ever so humble opinion, it's THE best rust proofing/inhibitor on the market today. I used it on my 1968 C10 and I can sand it down and paint over it, which I've done. I don't have any pics of what I did, but I have a link you can follow: Automotive Paints | Rust Bullet Rust Prevention Products | Concrete Paint | Corrosion Preventive Treatment Repair Remover Converter Thanks. I will check it out Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now