Jump to content

Adam DeRosa

AOAI Forum Members
  • Posts

    51
  • Joined

  • Last visited

Everything posted by Adam DeRosa

  1. So, you're measuring 9V at this wire while the engine is cranking, correct? If so, that may be OK. Verify by checking the Voltage at the battery while the engine is cranking. You'll probably see a similar drop.
  2. Jim - glad you got the problem with your brakes solved. In 1972 your car originally came with breaker points distributor, with power to the coil supplied by the Pink (with black stripe) resistance wire once running. During Start, full voltage was supplied to the coil by a Yellow by-pass wire that ran from the starter solenoid to the coil. With HEI ignition, you need full voltage to the coil all the time. You'll need to replace the Pink resistance wire. It should run to a connector on the steering column which you can get to if you crawl under the dashboard. You can then remove the resistance wire at the connector and run a new wire to the HEI system.
  3. @Zedman, that's a great video - thanks for sharing! Many years ago I had a terrible problem with the rear brakes locking up on my '72 Avanti during hard braking. I tried everything to solve it. I suspected the combination valve might be at fault but could not find a replacement at the time. I removed it and replaced it with an adjustable proportioning valve which solved my problem.
  4. Check the cigar lighter and make sure the wires are tight on the terminals and not loose and touching each other. I once had a similar problem and discovered it was caused by someone dropping a penny into the cigar lighter receptacle, causing an intermittent short circuit.
  5. Glad you got your overheating problem solved! Yes the transmission can be removed without removing the engine. This would also be a good time to examine the transmission mount and the driveshaft U-joints.
  6. Check this out, from Bob Johnstone's Avanti site: https://studebaker-info.org/Tech/Parts/2013/timkin50151s.html
  7. Yes, there is a filter inside the Q-Jet carb. There was also originally an external fuel filter with a return line to the tank. (by the way this return line to the tank is essential for preventing vapor lock when it's hot). Your '72 Avanti II was also originally equipped with with a charcoal vapor recovery canister as part of it's EPA emissions equipment. This would've been mounted on the right side of the engine along the inner fender. These also had fuel lines and hoses between the canister and the carb, and the canister and the tank. Someone on the past 53 years may have removed it, and one of these line could be the source of your leak.
  8. The T-fitting on the frame should have a pipe plug in the bottom of it, which can be removed for draining the tank. On the passenger side of the engine, there should be three lines at the fuel filter: - one line going into the filter -one going from the filter to the carb -one smaller line going from the filter back to the tank. Is it perhaps this smaller return line you're looking at? Sometime in the past someone may have made a "modification" that you may need to undo.
  9. It interesting that the moonroof would have this type of circuitry in it. Aside from the relay I can't imagine what the rest of it, like the IC's, would do. But, Avanti Motors did some strange things so who knows!
  10. Mike, Yes the tinted windows do help help the air-conditioning and reduce the heat load in the interior. It's also important to make sure unwanted heat isn't getting into the passenger compartment through leaks in the firewall, poor vent seals, etc. Here's a few pictures~ -Adam DeRosa
  11. Mike, Yes, I'm happy with the outcome. The window tinting does help although I can't say how much or to what degree. I live in AZ where the sun in brutal in the Summer, and if your car sits outside uncovered for any length of time it's going to get hot no matter what you do, but every little but helps.
  12. I had my windows tinted without removing them. I had to try a few shops before I found one that was willing to tackle it. It turned out great but I'm sure it was not easy to do the rear window. You may need to spend some time taking the car to different shops and getting estimates - some of them may be ridiculously high in hopes that you'll go elsewhere.
×
×
  • Create New...